StratasysSAF™

Stratasys H550

Stratasys H550 SAF industrial polymer 3D printer, front view

SAF powder bed fusion for larger parts and high-throughput polymer production.

System details

Stratasys H550 with the optional PowderEase T2 powder-handling system
With the optional PowderEase T2 powder-handling system
Powder fill lid on the Stratasys H550
Powder fill lid on the Stratasys H550
Interior sled assembly of the Stratasys H550
Interior sled assembly of the Stratasys H550
Small FPV drone illustrating an H550 component application
Small FPV drone illustrating an H550 component application
Ankle-foot orthosis illustrating an H550 application
Ankle-foot orthosis illustrating an H550 application
Large end-of-arm tooling illustrating an H550 application
Large end-of-arm tooling illustrating an H550 application
Motorbike fender components illustrating an H550 application
Motorbike fender components illustrating an H550 application

Engineering fit

Expand end-use polymer production with the Stratasys H550: a 34.2-litre build volume, a 450 mm longest axis and up to 50% higher throughput than H350, according to Stratasys. Commercial availability is planned for Q2 2027.

Larger parts. Higher throughput. Lower cost per part.

The Stratasys H550™ industrial polymer 3D printer expands SAF® production with a 34.2-litre build volume and a 450 mm longest axis. Manufacturers and service bureaus can produce larger components in a single piece or increase output through densely nested production builds. Stratasys states approximately 80% more build volume and up to 50% higher throughput than the H350.

Paired with the optional PowderEase™ T2, the H550 combines greater printing capacity with automated powder handling. One T2 is designed to support up to six H550 printers using the same material, helping production teams scale capacity while reducing manual handling between builds.

H550 versus H350: greater production capacity

The H550 has a 365 × 208 × 450 mm build envelope, extending the H Series platform from the H350’s 19.2-litre build volume to 34.2 litres. It is a separate printer, not a hardware upgrade to an existing H350. The larger envelope accommodates components that exceed the H350 build size and can reduce the need to split and join larger parts.

Stratasys reports more than twice as many parts per build compared with H350 in representative production nests, depending on part geometry and nesting strategy. Hundreds of components can fit into a single build, depending on component size and packing density. The specified SAF PA12 full-build print time is 16.5 hours; cooling, powder handling and finishing are additional stages. The up to 50% throughput comparison is a manufacturer claim, not a guaranteed improvement for every production mix.

Explore the Stratasys H350

Industrial production applications

For service bureaus and contract manufacturers, the larger build envelope broadens application coverage and supports repeat production of end-use parts. Unmanned systems and defence applications include UAV and drone frames, ducts, mounts, brackets, housings and larger unmanned-system components, alongside densely nested smaller parts.

Automotive and transportation applications include long bezels, trim, clips, connectors, brackets and functional housings. Industrial equipment and automation teams can use the platform for large fixtures, robotic end-of-arm tooling, grippers, adapters, industrial ducts, manifolds and manufacturing aids.

Orthotics and prosthetics applications include full-height ankle-foot orthoses, prosthetic sockets, insoles, splints, shells and supports. Aerospace applications include production tooling and suitable non-critical polymer components. Medical and aerospace end uses require application-specific validation and any relevant approvals; these examples do not establish certification of a printed part.

SAF PA12 and the printing workflow

The H550 is a powder bed fusion 3D printer powered by Selective Absorption Fusion (SAF). SAF PA12 is the launch material, with a 100-micron layer thickness. GrabCAD Print supports build preparation and workflow management; the technical specifications list the supported software workflow. Future materials remain subject to qualification and regional availability.

According to Stratasys, the core printing process uses powder and HAF fluid without detailing agents, cleaning rolls or customer-replaced printheads. Efficient nesting, powder recovery and reuse, and simplified consumables support the system’s production economics. Cost per accepted part depends on the production mix, utilisation and downstream workflow.

Explore SAF PA12

PowderEase T2: scale automated powder handling

PowderEase T2 automates build breakout, powder recovery and sieving, and dosing of the material blend for subsequent builds. Stratasys states that one T2 is designed to support up to six H550 printers using the same material. The combined H550 and T2 workflow is designed for less than 30 minutes of total operator time per build, excluding downstream part cleaning and finishing.

The expected automated breakout and dosing cycle is approximately 30–40 minutes, depending on production conditions. This elapsed automated cycle is distinct from operator time. Parts emerge partially depowdered and require subsequent cleaning or finishing appropriate to the application.

Plan an H550 production installation

Stratasys has announced commercial availability for Q2 2027. Register early interest through D2M’s existing consultation process to discuss planned production capacity, application suitability, equipment configuration and future H550 installations, including PowderEase T2 integration.

Use representative parts and production nests to assess output, part quality and cost per accepted part. Plan cooling, powder handling and finishing capacity alongside the printer fleet, and review electrical supply, extraction, environmental controls and equipment access against the technical specifications. Include operator training and service requirements in the installation plan.

Discuss your H550 plans and register early interest

Download the H550 specification sheet

Materials & process

Materials listed for this system

Specifications

Technical specifications

Product category

Industrial polymer 3D printer

Technology

Selective Absorption Fusion (SAF)

Effective build size (X × Y × Z)

365 × 208 × 450 mm

Effective build volume

34.2 litres

Layer thickness

100 µm (0.004 in)

Full-build print time

SAF PA12: 16.5 hours (print time only)

Powder material

SAF PA12

Fluid

Stratasys HAF High Absorption Fluid

Power requirements

400 VAC, 3P+N, PE, 50–60 Hz, 16 A

Power consumption

3.25 kW; 5 kW peak; 0.15 kW idle

Operating temperature

20–25 °C (68–77 °F)

Operating humidity

40–55% RH

Extraction rate

300 m³/h (177 CFM), with adjustable damper

Printer dimensions (W × D × H)

1900 × 940 × 1730 mm

Printer crate dimensions (W × D × H)

2156 × 1196 × 2100 mm

Printer weight

825 kg (1819 lb)

Crated printer weight

950 kg (2094 lb)

Network requirements

RJ45 Ethernet; 35 MBit network with DHCP server. Internet access recommended.

Supported software workflow

GrabCAD Print Pro; GrabCAD Print Server; GrabCAD Streamline Pro; Materialise Magics; Siemens NX; PTC Creo

Safety (supplier-listed)

EN ISO 12100:2010

Electromagnetic (supplier-listed)

Directive 2014/30/EU

Environmental and compliance entries (supplier-listed)

REACH; RoHS; WEEE; Modern Slavery Act; CoA; CoC; Conflict Minerals regulation; TSCA

Warranty

1-year limited warranty, including printheads and printer consumables

Service

Service plans include printheads and printer consumables

Consumables exclusions

Printer consumables exclude powders, HAF and maintenance materials such as cleaning fluids, gloves and swabs

Optional powder handling

PowderEase T2

Specification source

Stratasys PSS_SAF_H550_1026a; specifications subject to change without notice

Discuss your requirement

Review Stratasys H550 for your application

Analytics cookies

We use Google Analytics to understand what visitors find useful, where the site could be clearer, and how we can improve our pages. We do not send form details, uploaded files, or enquiry content to Google Analytics. With your consent, we also remember campaign links in this tab for up to 24 hours to understand how you reached an enquiry form.

Privacy Policy