Build envelope (XYZ) 406 × 355 × 406 mm
Industrial FDM for tooling and parts needing engineering thermoplastics.
Engineering fit
The Stratasys Fortus 450mc is an industrial FDM printer with a 406 x 355 x 406 mm build envelope. It is worth considering for manufacturing tools and selected functional parts when the required engineering or high-performance thermoplastic matters more than maximum part size.
Use the build envelope as a first check
The nominal XYZ envelope is 406 x 355 x 406 mm (16 x 14 x 16 in.). Place representative geometry in the intended build orientation with support and finishing allowances. A part whose bounding box fits may still need a different orientation, split construction or more room for its manufacturing route.
For fixtures and production aids, check locating surfaces, clamp loads, inserts, wear and service temperature. For functional parts, define the material requirement and inspection plan. Printer size and a material name do not establish acceptance of the finished part.
Materials & process
Let material requirements guide selection
Public supported examples include ABS-M30 and ASA, FDM Nylon 12CF, ULTEM 9085 and 1010 resins, and Antero 800NA. These routes address different requirements; they are not interchangeable. Check the current material, tip, layer-height and support combination for the selected machine configuration.
Support removal may be soluble or breakaway depending on the material. Build orientation influences part behaviour, so validate the relevant load direction and interfaces. OpenAM parameter access is an optional licensed route, not a reason to assume any material is qualified.
Materials listing this system
Compare the right FDM alternatives
For smaller general-purpose parts or reinforced-polymer tools, start with an F170/F370 or F190CR/F370CR comparison if its materials and envelope cover the workload. Consider the F870 for long tooling that suits its material set, the F900 for larger or taller parts with appropriate high-performance material options, and the F3300 when recurring production and operator intervention drive the decision.
The FDM comparison article below develops those trade-offs with examples. Use it to shortlist systems, then compare representative builds rather than selecting the largest envelope or assuming one machine is best for every job.
Evidence
Case study · Aerospace
East/West Industries
East/West Industries Fortus 450mc FDM Case Study
Read the case studyCNC Capacity Relief
The Fortus 450mc allowed East/West to print workholding fixtures instead of machining them, reducing pressure on CNC resources used for customer parts.
Nylon 12CF Production Support
Carbon fiber FDM Nylon 12CF was used for soft jaws, a replacement forming tool and other manufacturing aids tied to shop-floor needs.
Specifications
Technical specifications
- Build envelope (XYZ)
- 406 × 355 × 406 mm16 × 14 × 16 in.
- Machine size and mass
- 1,295 × 902 × 1,984 mm; 601 kgAllow additional working and service clearances.
- Electrical supply
- 208 VAC, three phase, 50/60 Hz, 18 AConfirm site provision before installation.
- Build envelope (XYZ)
406 × 355 × 406 mm (16 × 14 × 16 in.).
- Material delivery
Two model and two support canister bays, with automatic changeover.
- Process
Industrial FDM thermoplastic extrusion.
- Material examples
ABS-M30, ASA, FDM Nylon 12CF, ULTEM 9085 and 1010 resins, Antero 800NA. Check tip, layer and support compatibility.
- Machine size and mass
1,295 × 902 × 1,984 mm; 601 kg. Allow additional working and service clearances.
- Electrical supply
208 VAC, three phase, 50/60 Hz, 18 A. Confirm site provision before installation.
- Software
Insight and Control Center; compatible with GrabCAD Print and Print Pro. OpenAM requires an optional licence.
- Optional material cabinet
Fortus FDC delivery and drying cabinet: up to 8,194 cm³ of model material. Additional floor space required.
Optional Fortus FDC material delivery cabinet beside a Fortus 450mc
Discuss your requirement
Plan the cell and quotation
The OEM specifies a 601 kg machine and 208 VAC three-phase supply. Review access, floor space, site power, material storage, support processing and inspection before installation. An optional Fortus FDC cabinet adds material drying and delivery capacity; include it only where the workload justifies it.
D2M can review the application and implementation needs with GCC teams. Provide representative CAD dimensions, required material behaviour, expected build frequency and installation location. The quotation can then define system configuration, software, ancillary equipment, installation planning, operator training and support scope. The quote action keeps Fortus 450mc selected.